MENU
AAA

TERMONIUM parking (heavy duty floor)

  • flat roofs,
  • industrial floors (factories, shops and warehouses),
  • parking areas and garages,
  • insulation of upper tie beams, lintels and other thermal bridges,
  • driveways

The product complies with the harmonized standard EN 13163:2012.

TERMONIUM parking EPS 150    EPS-EN 13163-T(2)-L(3)-W(3)-S(5)-P(10)-BS200-CS(10)150-DS(N)2-DS(70,-)2-DLT(1)5

Those are white and orange, might be “spotted,” boards produced by foaming polystyrene and intended for thermal insulation of floor, roofs, flat roofs and car parks. The boards may be produced with flat or milled edges enabling proper fitting. The boards are manufactured in standard dimensions: 1000 mm long, 500 mm wide, 10 mm thick, and then every 10 mm. A compressive creep deformation of 2% or less, when subjected to a permanent compressive stress of 45 kPa (4500 kG/m2).

Polystyrene subjected to voluntary certification and recommendation procedure at Building Research Institute (Polish: ITB), not resulting from the system of assessment and verification of performance constancy.

Declared properties of TERMONIUM parking expanded polystyrene boards:

Dimension tolerance classes:  
  • thickness
  • T(2)± 2 mm
  • length
  • L(3)± 0,6% lub ± 3 mm*)
  • width
  • W(3)± 0,6% lub ± 3 mm*)
  • rectangularity
  • S(5)± 5 mm/m
  • flatness
  • P(10) 10 mm
    Bending strength levelBS200≥ 200 kPa
    Compressive stress at 10% relative deformationCS(10)150≥ 150 kPa
    Class of dimensional stability under constant normal laboratory conditionsDS(N)2± 0,2%
    Level of dimensional stability under specified temperature and humidity conditions (temp. 70°C, 48 h)DS(70,-)2 2%
    Deformation under specified compressive load and temperatureDLT(1)5≤ 5%
    Declared thermal conductivity ratio λD at a temperature of 10°C0,035 W/(m*K)
    Fire reaction classE

    *)Value which offers higher tolerance.

    Declared value of thermal resistance RD depending on the thickness of TERMONIUM parking boards

    Thickness, mm102030405060708090100
    RD, m2K/W0,250,550,851,101,401,702,002,252,552,85
    Thickness, mm110120130140150160170180190200
    RD, m2K/W3,103,403,704,004,254,554,855,105,405,70

     Implementation

    The EPS boards should be applied in accordance with the manufacturer’s instructions, RTQ ITB-1261/2013 Technical and Quality Recommendations, and guidelines contained in a construction design. The basic guidelines for laying the thermal insulation of floors and ceilings are as follows: make sure that the basis is flat and dry, otherwise flatten it. The floors on the ground require a damp proofing barrier (in form of tar paper, PE film, bituminous, water-based sealants). In case of ceilings between floors, apply a separating layer of PE film. Where the floor meets the wall, joint filler tape should be used. Start laying the boards in the corner and place the first row of boards from the wall by pushing them against the joint filler tape. Subsequent rows should be laid with staggered joints, without crossing the junctions of boards. When all insulation is in place (can be in two or more layers), spread at least 0.2 mm thick PE film to protect the boards from moisture and penetration of underlayment into the spaces between the EPS boards. Where water-based underfloor heating is used, install the heating cables with suitable board clips on which the PE film has already been spread. Please take into account that the thickness of the underlayment needs to be increased by the outer diameter of underfloor heating pipes.

     Caution

    Do not use the EPS boards in direct contact with the substances having destructive effect on polystyrene EPS, such as organic solvents (acetone, benzene, nitro), etc.

     Package, storage, transportation

    TERMONIUM parking boards are supplied only in the original manufacturer's packaging. The label on a package contains the following information: the name of a product, the manufacturer's name and a factory name, the date of production, EN 13163:2012 standard number, a code compatible with that standard, and declared technical features. TERMONIUM parking boards should be protected against damaging and weather conditions.

    Technical sheet TERMONIUM parking (heavy duty floor)(42.79KB)pdf  download
    Declaration of Performance TERMONIUM parking (heavy duty floor) 012-DoP-170630(1.31MB)pdf  download
    Certification Mark(0.55MB)pdf  download
    Certyficate of conformity ITB-851W(1.97MB)pdf  download

    MAYBE YOU WILL BE INTERESTED IN

    GOLD parking (heavy duty floor)
    Latex Paint LATEX MATT
    Silicone Plaster TO-TS
    Back